Engine

MITSUBISHI

All Top Line, Short Blocks, and Complete Engines, are Sold Outright No Core Charges!

Back to Engine Menu

Call For Pricing 1-877-354-3812

CE= Complete Engine as Follows:
(short block as below) assembled with complete cylinder head, and all timing componets and oil pump. No oil pan, valve covers, or manifolds

SB= Short Block as Follows:
machined and assembled with over-size pistons, rings, matching crank kit, connecting rods and camshaft (if applicable)

EKM= Main Engine Kit as Follows:
contains complete gasket set, set of pistons and rings, main bearings, rod bearings, thrust washers, timing belt, balance shaft bearings (if applicable), and set of expansion plugs (does not contain camshaft, timing kit or oil pump)

Warranties:
A 12 month or 12,000 mile warranty applies to all parts. The original purchaser must make claims for warranty inspection.

Contact Topline for a Repair or Return Authorization Number before proceeding with any warranty work. Have the following information ready when calling: Date of original purchase, Invoice number, Topline part number, a description of the nature of the problem, mile at installation, mileage at failure, and the Engine warranty number for long block and short block purchases. This information must also accompany any return. If a repair is minor, only Topline can authorize that the installer can make a repair. Invoice copies for parts and labor must accompany defective parts. This documentation must be marked with the Return Authorization Number and returned to Topline with the defective part. When making a component claim, all contacting parts must be returned with the alleged defective component to receive a credit; i.e. cam and lifter and rockers with a cylinder head, or rods and bearings with a crankshaft, etc. No credits will be issued until the alleged defect is received and inspected by Topline.

Labor claims cannot exceed $250.00 on a complete engine, $100.00 on a short block. Cylinder head warranties are limited to replacement of head and head set within 90 days of purchase date. No labor claims will be paid on water pumps. Warranties are limited to replacement of the water pump. Hydraulic tensioners are typically sourced from OEM factories, and due to their nature, labor claims on these hydraulic tensioners are limited to replacement only. All other labor claims will be paid at a flate rate of $30 per hour from the Mitchell Flat Rate Manual to a maximum of 10 hours. Credit is issued in the form of a merchandise credit only.

Engine warranties will only be honored if the Topline Installation Checklist is properly filled out, signed by the installer, and returned to Topline within two weeks after the date of installation. Any repair work done without a Repair Authorization Number will void any warranty coverage.

Topline will not be responsible for any damages due to freight, fire, accident, obvious abuse, neglect, or situations where installed used parts cause damage to new parts. The heat tabs must be in place on engines, and not altered or melted. Crankshafts must be inspected for specifications before installation or warranty is void. Parts and engines used for industrial purposes will not be warranted. Bearings, pistons, and rings must be inspected for proper size before installation or warranty is void. No warranty will be honored on heads where heat tabs have been removed, melted or altered. No warranty will be honored on heads where the defect is due to warpage from overheating or the installation of used cams, lifters, or rockers. No warranty will be honored when the cause is found to be oil contamination. It is the responsibility of the installing mechanic to make sure that parts are correct before installation.

Topline does not assume any responsibility for towing charges, fluids, freon, fuel, filters, lay-up time, lodging, car/truck rental or other substitute transportation, telephone charges, travel, damage to personal property, commercial loss, normal diagnostic time, loss of revenue or other matters not specifically included.

Check and replace when needed, the radiator, hoses and belts, fan switch, water and oil pumps, cylinder head bolts, thermostat, fuel mixture, timing and catalytic converter before proceeding with repairs. If you replace your head, pistons, or other parts without determining the actual reason for failure, the new parts will be damaged too!

WARRANTY NON-TRANSFERABLE:
VALID ONLY TO ORIGINAL PURCHASER

Home| About Us | Machine Work | Policies | Contact Us

RPM Machine Inc.
9529 So. 500 W. • Sandy Utah 84070
(ph) 801-676-0038• (fax) 801-568-3441• (email) RPM Machine@direcway.com
  Toll Free 1-877-354-3812

Don't forget to bookmark this site.